✎ pidflight:bluetooth [rotorOverflow]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== PIDflight Lap ======
===== How to setup Bluetooth module for lap timing device =====
By default most modules are set to **9600** baud rate. The Bluetooth module must be configured to **115200** baud rate. 

Please be aware the AT commands to configure your Bluetooth module may vary. Below are examples of typical AT commands for most common modules. 

===== HC-06 =====
  - Connect the HC-06 to PC with an FTDI adapter (ensure RX and TX are crossed over). 
  - Open a serial terminal to the COM port on baud rate 9600.
  - Type "**AT**" into the terminal, a "**OK**" response should be returned. Proceed to step 4.
  - Type "**AT+BAUD8**" into the terminal, a "**OK115200**" response should be returned. 
  - All done! 

The following AT commands are used to configure the name and passcode on the Bluetooth module.
  * **AT+NAME<new name>** (e.g AT+NAMEPIDflight to set module name to "PIDflight") 
  * **AT+PIN<XX... X>** (e.g AT+PIN0000 to set module pairing pin to "0000")

==== Alternative ====
An alternative option to setting up the Bluetooth module without an FTDI adapter is the use the **bluetooth-hc06.hex** with an Arduino Nano.

  - Connect the HC-06 to Arduino Nano:
    - Arduino (5V) -> HC-06 (VCC)
    - Arduino (D6) -> HC-06 (TX)
    - Arduino (D7) -> HC-06 (RX)
    - Arduino (GND) -> HC-06 (GND)
  - Flash the {{:pidflight:bluetooth-hc06.zip|}} HEX file to the Arduino Nano.
  - Once the HEX file has been flashed, allow 5 seconds for the Bluetooth module settings to take effect.
  - Done.

The **bluetooth-hc06.hex** will set the HC-06 Bluetooth module name to **PIDFLIGHT** and baud rate to **115200**.

===== HM-10 =====
This module is **supported** as of PIDflight Lap **v1.0.0-alpha.5**.

**This module should be set to 9600 baud rate by factory default and require no further changes.**

If you need to configure your HM-10 module to use baud rate 9600, following these steps:
  - Connect the HM-10 to PC with an FTDI adapter (ensure RX and TX are crossed over). 
  - Open a serial terminal to the COM port on baud rate 9600.
  - Type "**AT**" into the terminal, a "**OK**" response should be returned. Proceed to step 4.
  - Type "**AT+BAUD0**" into the terminal, a "**OK+Set:1**" response should be returned. 
  - All done! 

^Parameter^Baud rate^
|0|9600|
|1|19200|
|2|38400|
|3|57600|
|4|115200|
|5|4800|
|6|2400|
|7|1200|
|8|230400|

**IMPORTANT**: Please be careful, if you set the baud rate to 1200, the module may no longer support the configurations of the AT command. You may need to short-circuit the PIO0 to ground to restore factory settings.

The following AT commands are used to configure the name and passcode on the Bluetooth module.
  * **AT+NAME<new name>** (e.g AT+NAMEPIDflight to set module name to "PIDflight") 
  * **AT+PASS<XX... X>** (e.g AT+PASS0000 to set module pairing pin to "0000")
  * **AT+RENEW** to restore factory settings, recommend to issue a **AT+RESET** afterwards to restart the device with factory settings.
  * **AT+ROLE0** to set the module as slave.
User Tools

Site Tools

Page Tools
