This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
pidflightlap:protocol [2019/02/08 09:58] cmengler [MSP codes] |
pidflightlap:protocol [2019/02/08 20:15] cmengler [MSP codes] |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ===== Notes ===== | ===== Notes ===== | ||
| - | * By default all lap timers are activated. | + | * By default all lap timers are activated on power up. (i.e. do not require **MSP_ACTIVATE** to be sent) |
| ===== Getting started ===== | ===== Getting started ===== | ||
| Line 17: | Line 17: | ||
| ===== MSP message format ===== | ===== MSP message format ===== | ||
| + | {{:pidflightlap:msp_message_format.png?nolink&800|}} | ||
| ===== MSP codes ===== | ===== MSP codes ===== | ||
| ^Name^Code^Description^ | ^Name^Code^Description^ | ||
| - | |MSP_API_VERSION|1|| | + | |MSP_API_VERSION|1|Firmware API version| |
| - | |MSP_STATUS|4|| | + | |MSP_STATUS|4|Device and lap timing status| |
| - | |MSP_RESET|5|| | + | |MSP_RESET|5|Resets device and lap timing state| |
| - | |MSP_RSSI_CALIBRATE|6|| | + | |MSP_RSSI_CALIBRATE|6|Triggers RSSI calibration routine| |
| - | |MSP_START|7|| | + | |MSP_START|7|Starts lap timing| |
| - | |MSP_ACTIVATE|8|| | + | |MSP_ACTIVATE|8|Activates a lap timer device| |
| - | |MSP_DEACTIVATE|9|| | + | |MSP_DEACTIVATE|9|Deactivates a lap timer device| |
| - | |MSP_DEVICE_ID|10|| | + | |MSP_DEVICE_ID|10|Not used| |
| - | |MSP_SET_DEVICE_ID|11|| | + | |MSP_SET_DEVICE_ID|11|Triggers lap timing devices to assign an ID| |
| - | |MSP_CHANNEL|20|| | + | |MSP_CHANNEL|20|Gets the channel frequency set on the lap timing device| |
| - | |MSP_SET_CHANNEL|21|| | + | |MSP_SET_CHANNEL|21|Sets the channel frequency on the lap timing device| |
| - | |MSP_CURRENT_LAP|30|| | + | |MSP_CURRENT_LAP|30| | |
| - | |MSP_LAP_MIN_TIME|34|| | + | |MSP_LAP_MIN_TIME|34| | |
| - | |MSP_SET_LAP_MIN_TIME|35|| | + | |MSP_SET_LAP_MIN_TIME|35| | |
| - | |MSP_LAP_MAX|37|| | + | |MSP_LAP_MAX|37| | |
| - | |MSP_SET_LAP_MAX|38|| | + | |MSP_SET_LAP_MAX|38| | |
| - | |MSP_RSSI|40|| | + | |MSP_RSSI|40| | |
| - | |MSP_RSSI_THRESHOLD|42|| | + | |MSP_RSSI_THRESHOLD|42| | |
| - | |MSP_SET_RSSI_THRESHOLD|43|| | + | |MSP_SET_RSSI_THRESHOLD|43| | |
| |<del>MSP_RSSI_FILTER</del>|44|TBD| | |<del>MSP_RSSI_FILTER</del>|44|TBD| | ||
| |<del>MSP_SET_RSSI_FILTER</del>|45|TBD| | |<del>MSP_SET_RSSI_FILTER</del>|45|TBD| | ||
| |MSP_EEPROM_WRITE|250|Persists settings to EEPROM for settings to survive a power cycle (if desired)| | |MSP_EEPROM_WRITE|250|Persists settings to EEPROM for settings to survive a power cycle (if desired)| | ||
| + | |||
| + | ==== MSP_API_VERSION ==== | ||
| + | ^Part^Type^Description^ | ||
| + | |1|UINT 8|Major version| | ||
| + | |2|UINT 8|Minor version| | ||
| + | Version is constructed as [PART 1][DECIMAL][PART2][DECIMAL][ZERO] (e.g. 2.6.0) | ||
| + | |||
| + | ==== MSP_STATUS ==== | ||
| + | ^Part^Type^Description^ | ||
| + | |1|UINT 8|Device state| | ||
| + | |2|UINT 8|Timer state| | ||
| + | |||
| + | === Device states === | ||
| + | ^Value^State^ | ||
| + | |0|Idle| | ||
| + | |1|Timing| | ||
| + | |2|Calibrating| | ||
| + | |3|Inactive| | ||
| + | |||
| + | === Timer states === | ||
| + | ^Value^State^ | ||
| + | |0|Waiting| | ||
| + | |1|Start| | ||
| + | |2|Stop| | ||
| + | |||
| + | |||
| + | |||
